SBS 2000, 2 NICs, DYNAMIC IP, ISA [PROXY SERVER],  with RASPPPoE

Courtesy Susan Bradley/Merv Porter/Bill Sanderson

[UNDER CONSTRUCTION NOT FINISHED YET]

While the preferred method is to implement a PPPoE router and not install this software, there are many reports that this software does work and does not cause issues that other PPPoE software has caused when loaded on servers.

In order to implement this version you will need to download and install this software:

PPP over Ethernet Protocol, Version 0.96: RASPPPOE_096.ZIP

Please read this page IN FULL before implementing this installation:

RASPPPOE Home Page:
http://user.cs.tu-berlin.de/~normanb/

 

Please also review user comments on the SBS2K newsgroup

Additional resources can be found:

Carrick Solutions Limited - RASPPPoE:
http://www.carricksolutions.com/raspppoe.htm

broadband RASPPPoE:
http://www.dslreports.com/forum/robpppoe
broadbandreports.com - the place for BROADBAND:
http://www.dslreports.com/pppoe

 

 

 


 

 

 

Please note the recommended DNS setup is noted in this KB article:

How to Use the IP Address of Your Internal Network Adapter for DNS:
http://support.microsoft.com/default.aspx?scid=http://support.microsoft.com/highlights/sbstopdns.asp

 

Additional Setup

 

a.        Right click My Network Places...Properties. Right click on Internal NIC. Under the General tab, you should have the following checked:

Microsoft Client for Networks

QoS Packet Scheduler

File and Printer Sharing

Internal Protocol (TCP/IP)

 

b.       Right click My Network Places...Properties. Right click on External NIC. Under the General tab, you should have the following checked:

Internal Protocol (TCP/IP) - nothing else


c.   Right click My Network Places...Properties. Highlight the Internal NIC. Then select Advanced...Advanced Settings from the top menu for that window. This will check the bindings.

d.   DHCP setup. Click on Start...Administrative Tools...DHCP.

Address Pool: 192.168.16.0 to 192.168.16.254

Scope Options:

003 Router 192.168.16.2

006 DNS Servers 192.168.16.2

015 DNS Domain Name yourcompany.local

044 WINS/NBNS Servers 192.168.16.2

046 WINS/NBT Node Type 0x8

[please note - in official release notes, this value is usually seen as 0x1 (type B), however 0x8 is recommended for a SBS server]

e. Internet Connection Wizard (ICW)

Start the SBS Admin Console and run the ICW.

When prompted: Select Broadband Connection

When prompted: Select External NIC

When prompted: Use the DNS Nameservers from your ISP as DNS Forwarders.

 

f. Check to make sure the External NIC IP address is not included in the
        LAT range.

 


 SBS Console | Internet Security and Acceleration Server 2000 | Servers and
Arrays | <SBS Server Name> | Network Configuration | Local Address Table
(LAT)

Example:

If the external NIC has an IP address of 192.168.1.2 and the Internal NIC
has an IP address of 192.168.16.2, then the range in the LAT should be
192.168.16.0 to 192.168.16.255 (which excludes the external NIC).

 


Please note:  While the suggested IP addressing schema of the SBS 2000 is 192.168.16.x, you can utilitize any private IP address as recommended.  Thus if you have a prior set up of 10.0.0.x, you may use that as well.  When attaching Win98, or WinME computers, you may need to use hosts and lmhosts files to assist them in attaching to the network.  Please see http://www.sbs2000.info click on logon problems for additional detail.

 

For additional features that can normally only be done with a static IP address, you may wish to sign up for dynamic DNS services such as www.dns2go.com or www.tzo.com that will provide you with these abilities.  You will need to install this software on your server and open up a port in ISA Server as follows:

Name :[Insert your own]
enabled
custom
ip protocol: TCP
direction: both
local port: all ports
Remote port: Fixed port
Remote port number: 1227